USPP is a computer temperature controller, which maintains the desired temperature, and measures the time specified. The controller can be used to control electric furnaces or other. The driver version is performed with control: Simple-type PID control as well as a hysteresis. The versatility of the solution enables the use of driver USPP also in other applications where it is necessary to maintain the temperature and timing. The parameters set during the programming process are saved to nonvolatile memory controller. There is no need to set the parameters again after power.

USPP controller is dual channel controller, performs at the moment to maintain the temperature independent for the two channels. The program reads the temperature of two temperature sensors, controls the contactors or team triacs or thyristors. Because of the two sensors the controller can also act as a regulator of a two-time metering, or two independent single-channel temperature controllers.

All parameters set during programming are entered via the keypad foil covering the front panel. The measured temperature value of the selected channel is continuously presented on the display. Time elapses is presented on a separate display. The front panel of the controller are LEDs, or at the time the outputs are enabled or disabled. Indicated are also alarm LED ALARM (exceeding the allowable temperature, actuator failure, sensor failure). Each channel has two independent outputs included an enabled power-sharing within a single channel. In addition, the controller has two independent outputs a voltage turn-off to control the inclusion of additional functions such as lighting, ventilation, condensation, etc. The controller has a sound signal indicating the completion of measuring the set time (eg end of baking).

The power supply is 230 VAC, in the case of power failure the controller state is stored in nonvolatile memory so that when power is interrupted the process continues. The value of the supply voltage can be tailored to individual customer needs. The device is placed in a module in a metal housing with dimensions of 90x90x120 mm and 96x96 mm front panel or a plastic housing with dimensions of 90x90x100 mm and 96x96 mm front panel. The controller can operate in an ambient temperature of 0 - 60 ° C.

Because of the versatility to go out and easy to install the driver can be used both in new furnaces already in operation as well.

implemented functions:

• thermal process control
• maintain the temperature,
• timing,
• number of temperature measurement inputs: max 2
• measured temperature range 999 ° C
• Maximum length of time measured 99 min or 99h
• type of temperature sensor: thermocouple or PT100
• Control: contactors, triacs, thyristors
• Control type: Simple-PID or hysteresis
• sound signaling the end of timing
• alarm signals:
  - exceeding the allowable temperature
  - damage to the actuators (relay, triac)
  - sensor failure
• non-volatile memory to memorize the set of parameters
• continuation of the process after power failure
• be used as a two-level controller
• Typical applications: control of the bakery ovens

inputs	resistance thermometer	Pt100
	Thermocouples	J, K, N
	linear sensors	0-1V, 0-10V, 0-20mA, 4-20mA
	range	Dependent on the type of input
output	Relay	5A/250VAC, resistive load
	voltage	On request: 5VDC, 8VDC, 15VDC
programming	The programming	The keyboard 2 modes of operation: programming, normal operation
	The security parameters of the programming	Automatic locking when working
control	Pulse Range PID	Programmable, 2 - 15 ° C
	PID cycle time	Programmable, 4-32 sec
	ON - OFF	You can work on / off (selectable programmable) with adjustable hysteresis (0 - 15°C)
	regulatory action	You can work for heating / cooling
Power Supply	voltage	190-250VAC On request: 24VAC or DC, 12VAC or DC
	power consumption	4VA
alarms	Exceeding the scope of	The signal light and sound - pulsing
	sensor failure	The signal light and sound - pulsing
	Damage to the power circuit	Light and sound signal - a continuous
other	memory	Protection against power outages, Enduring memory parameter setting value
	digital display	3 + 2 digits (green - 14mm)
	display range	999 - temperature: 99 - Time
	degree of protection	From the front IP54, IP20 total
	operating temperature	0 - 60 ° C
	humidity	80% without condensation
	weight	950g
	Sizes	WxSxG (96x96x130mm)
	Mounting Hole Dimension	WxS (91x91mm)
	Mounting plate thickness	to 8mm
	Faceplate Color	gray, green, another to the arrangements

terminal description


Types of measuring inputs

code	sensor	range
1	Thermocouple J	0 - 800°C
2	Thermocouple K	0 - 999°C
3	Thermocouple N	0 - 999°C
4	Pt100	0 - 750°C
5	0 - 1 V	-------
6	0 - 20 mA	-------
7	4 - 20 mA	-------