USPP-G is a microprocessor temperature controller that maintains the desired temperature, and measures the time specified. The controller can be used to control gas or oil furnaces bakery. The controller provides total control of furnace operation, controlling the air circulation fan, burner, fogging and lighting in the oven. Control is achieved through built-in relays. The parameters set during the programming process are saved to nonvolatile memory controller. There is no need to set the parameters again after power.

USPP controller reads the temperature of two temperature sensors, controls the contactors or team triacs or thyristors. Because of the two sensors the controller can be made in the second preview version of the entry or controlled by averaging measurements from two measuring inputs. All parameters set during programming are entered via the keypad foil covering the front panel. The measured temperature value of the selected channel is continuously presented on the display. Time elapses is presented on a separate display. The front panel of the controller are LEDs, or at the time the outputs are enabled or disabled. Indicated are also alarm LED ALARM (exceeding the allowable temperature, actuator failure, sensor failure). The controller has a sound signal indicating the completion of measuring the set time (eg end of baking).

The power supply is 230 VAC, in the case of power failure the controller state is stored in nonvolatile memory so that when power is interrupted the process continues. The value of the supply voltage can be tailored to individual customer needs. The device is placed in a module in a metal housing with dimensions of 90x90x120 mm and 96x96 mm front panel or a plastic housing with dimensions of 90x90x100 mm and 96x96 mm front panel. The controller can operate in an ambient temperature of 0 - 60 ° C.

Because of the versatility to go out and easy to install the driver can be used both in new furnaces already in operation as well.

Implemented functions:

• maintain the temperature,
• timing,
• number of temperature measurement inputs: 2
• measured temperature range 999 ° C
• Maximum length of time measured 99 min or 99h
• type of temperature sensor: PT100 or Thermocouple
• Control: contactors, triacs, thyristors
• Control type: hysteresis
• sound signaling the end of timing
• alarm signals:
  - exceeding the allowable temperature
  - damage to the actuators (relay, triac)
  - sensor failure
• non-volatile memory to memorize the set of parameters
• continuation of the process after power failure
• Typical applications: control of gas and oil furnaces

inputs	resistance thermometer	Pt100
	Thermocouples	J, K, N
	linear sensors	0-1V, 0-10V, 0-20mA, 4-20mA
	range	Dependent on the type of input
output	Relay	5A/250VAC, resistive load
	voltage	On request: 5VDC, 8VDC, 15VDC
programming	The programming	The keyboard 2 modes of operation: programming, normal operation
	The security parameters of the programming	Automatic locking when working
control	ON - OFF	Work on / off switch with adjustable hysteresis (0 - 20°C)
Power Supply	voltage	190-250VAC On request: 24VAC or DC, 12VAC or DC
	power consumption	4VA
alarms	Exceeding the scope of	The signal light and sound - pulsing
	sensor failure	The signal light and sound - pulsing
	Damage to the power circuit	Light and sound signal - a continuous
other	memory	Protection against power outages, Enduring memory parameter setting value
	digital display	3 + 2 digits (green - 14mm)
	display range	999 - temperature: 99 - Time
	degree of protection	From the front IP54, IP20 total
	operating temperature	0 - 60 °C
	humidity	80% without condensation
	weight	950g
	Sizes	WxSxG (96x96x130mm)
	Mounting Hole Dimension	WxS (91x91mm)
	Mounting plate thickness	to 8mm
	Faceplate Color	gray, green, another to the arrangements

terminal description


Types of measuring inputs

code	sensor	range
1	Thermocouple J	0 - 800°C
2	Thermocouple K	0 - 999°C
3	Thermocouple N	0 - 999°C
4	Pt100	0 - 750°C
5	0 - 1 V	-------
6	0 - 20 mA	-------
7	4 - 20 mA	-------