WATER FEEDER - Mixer with chilled water input is a device equipped with a microprocessor controller, designed for measuring the flow of the water required at a specific temperature. Especially useful for metering of water is needed in various technological processes carried out periodically, in which the temperature plays an important role in processes such as in food industry (bakery, confectionery, pasta production, etc.)

FEEDER - mixer is adapted to receive hot and cold water directly from the water supply and chilled water from the cooler for example.
Dispenser has a built in mixer that allows for fast water outflow at the desired temperature.
The mode of ice water mixed chilled water unit with cold water, thus obtaining a minimum flow of chilled water. Dispensers of our production are new, yet proven and tested product that is constantly improved and developed in based on feedback from existing users.

All dispensers are fully automatic. Thanks to modern solutions, eliminating the mechanical dial. Control unit is an electronic dispenser USP microprocessor controller designed and manufactured by our company based on the latest electronics. Driver software is also done in our company so we can immediately respond to the suggestions reported by current users. Devices have built-in automatic adjustment of water temperature during dosing, depending on the temperature of the water already poured out. This allows water to obtain the desired temperature without having to dump the water. Moreover, the devices have self-learning function, which helps shorten the minimum time to reach the desired temperature.

Actuators (solenoids, actuators, valves, mixers, flow sensors) mounted dispensers are of the highest quality and are manufactured by world-renowned companies such as: Rossweiner, Danfoss, Esco, Hankook Gas and others.

Differences between the versions:
PROG version is enriched with additional programs. In 20 programs, you can remember the amount of water and its temperature to a cake recipe. No need to remember these parameters, just call the appropriate number of the program, described on the cover of the dispenser.

water connections	How to Connect	Screw connection ½ / ¾ inch or hose ½ / ¾ inch
programming	The programming	Using the keypad, 4 function keys, 5 keys to set values​​, the two modes of operation 20 programs: the quantity and temperature of the water
	The work programs (version PROG) programmable parameters: temperature correction flow coefficient	+/- 5 °C 10.0 - 90.0 typical: 74.0 for ½ cala                                    18.0 dla ¾ cala
Setting	set size: Measured quantity of water Outflow water temperature (programmable from the keyboard)	0.1 - 99.9 liters (or 1-999 liters) 1 -70 °C
water pressure	maximum Maximum pressure difference between the input terminals	5 bar 2 bar
flow	Minimum	1.50 l/min for ½ inch 3.00 l/min for ¾ inch
	maximum	25.0 l/min for ½ inch 60.0 l/min for ¾ inch
	measurement error	+/-1.5%
Power Supply	voltage	230VAC +/-10% 50Hz
	Maximum power consumption	13VA
alarms	Over range (alarm at 97 deg C)	Intermittent light and audible signal
	Temperature sensor failure	Intermittent light and audible signal
	No signal from flow sensor with an open discharge	Intermittent light signal
	Presentation by signals from the sensor with a closed discharge	Continuous light signal and the intermittent sound
other	memory	Protection against loss of supply voltage, nonvolatile flash memory parameter setting value. 20 temperature settings and the amount of water (PROG version), memory 100 most recent operations.
	digital display	3 + 2 digits (red 14 mm)
	degree of protection	From the front IP54, IP20 total
	installation Category	I
	degree of pollution	I
	fuse	2 x 600 mA typu M lub T
	operating temperature	0 - 45 ° C
	humidity	80% without condensation
	weight	10,5 kg - 1/2" 13.5 kg - 3/4"
	Case Size	WxSxG (300x390x175mm)
	housing material	stainless Steel
	Hole Spacing	335 mm
	Spacing of connections (from left)	cold - 70mm - hot - 70mm - ice
	Faceplate Color	gray